2.85mm Volcano PLA - Black

2.85mm Volcano PLA - Black

Kaubamärk: Formfutura
Tootekood: 8718924479056
Ühik: tk 750g
Tarneaeg: 3 päeva
Hind: 36,48 €
Kogus: tk 750g Lisa korvi

Volcano PLA

 

Volcano PLA on disainitud tööstuslikuks kasutamiseks PLA lõng. Volcano PLA-l on suurem printimise kiirus ja parem kuumakindlus kui tavalisel PLA lõngal. Volcano PLA pakub sarnaseid mehaanilisi ja temperatuuri omadusi nagu enamus ABS lõngasid. Samas see on biolagunev ja lihtne printida.

 

High heat resistant, high print speed, high impact strength

 

Volcano PLA is an industrial grade PLA which is engineered for professional applications that require high printing speeds and improved heat resistance and mechanical properties similar to ABS.

Volcano PLA offers the same mechanical and thermal properties - after annealing - as most ABS filaments, but with the biodegradability and ease of printing of PLA. Volcano PLA combines a high heat resistance with high printing speeds and high impact resistance into a PLA-based filament engineered for industrial applications.

 

Unique features

  • High heat resistance of ≥ 95° C after annealing
  • Less than 0.3% shrinkage after annealing
    • Roughly 8 times less shrinkage compared to competitor materials available on the market
    • Engineered to have excellent dimensional accuracy before and after annealing
  • Engineered for high printing speeds of > 120mm/s
    • Highly crystalline immediately after extruding resulting in increased stiffness and temperature resistance
  • Superb mechanical properties comparable to ABS
  • Excellent interlayer adhesion
  • Biodegradable
  • Matte surface finish

 

 

General printing guidelines *

 

Nozzle size: ≥ 0.15mm

Layer height: ≥ 0.1mm

Flow rate: ± 100%

Print temp: ± 220 - 255° C

Print speed: High

Retraction: Yes ± 5mm

Heat bed: ± 0 - 60° C

Fan speed: 50-100%

Experience level: Beginner

 

*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.

 

Annealing Volcano PLA

Annealing is a secondary process in which a plastic part is heated up to half of the melt temperature for a moderate period of time before letting the plastic part cool back down to room temperature.

When the plastic part is reheated (annealed) like this, the material relaxes and internal stresses and/or strains are relieved resulting in improved dimensional stability, reduction/removal of dimensional distortion and defects, and improved physical and thermal properties of the printed (and annealed) plastic object.

 

 Step 1

Preheat a convection oven at 110° C (half the melting temperature of Volcano PLA).

It is highly recommended to use a thermometer to calibrate the exact temperature of your convection oven.

 Preheating the oven to 110° C is extremely important as your Volcano PLA printed object will then crystalize in such a rapid timeframe that there is almost no time for the material to shrink. This results in a negligible shrinkage percentage of < 0.3% and by that Volcano PLA is unsurpassed when it comes to reduction of shrinkage after annealing.

 Step 2

When the oven is preheated to a stable temperature of 110° C then quickly put your Volcano PLA printed object in the oven. Make sure to do this as quick as possible in order to keep the loss of heat reduced to a minimum. Don’t remove any supports (if used) from the printed object when putting it in the oven.

 It is recommended to place the Volcano PLA printed object on a flat aluminium sheet/foil  or similar flat metal object to obtain a stable/equal heat transmission.

 Small objects – 20 minutes timer

For small objects with thin walls and medium infill annealing will take ± 20 minutes

 Large objects – 60 minutes timer

For large objects with thick walls and medium/high infill annealing take ± 60 minutes

 Step 3

When the object is annealed taking above mentioned duration into account then switch off the oven and let it cool down to room temperature. Do not remove the object before the oven has completely cooled down to room temperature!

 Step 4

When the oven is cooled down completely you remove the object from the oven and remove any support material (if used). Your Volcano PLA printed object is now annealed and has all thermal and mechanical properties as displayed in the Technical Data Sheet (TDS).

  

Filament length

ρ: 1.27 g/cc

50 gr coil

0.75 Kg spool

2.3 Kg spool

4.5 Kg spool

8 Kg spool

Ø 1.75mm

± 16.4m

± 246m

± 753m

± 1473m

± 2619m

Ø 2.85mm

± 6.2m

± 93m

± 284m

± 555m

± 987m

 

Product export information

 

HS Code: 39169090

Description: Monofilament

Country of origin: the Netherlands

 

Compliance *

This filament is compliant to below listed directives and regulations.

  • RoHS directive 2011/65/EC
  • REACH directive 1907/2006/EC

 *) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.